Bob Hart’s Rumford Fireplace Forms

Instructions

1. Foundation

2. Hearth and Hearth extension

3. Building the firebox

4. Setting Bob Hart’s Rumford Fireplace forms in  place

5. Pouring the throat and lintel

6. Transition to flue

7. Chimney

        8. Top Mount Damper

(Click each picture to see it full size, then use your Web browser's Back button to return to this page.)

Foundation

As with any masonry chimney, the foundation should be adequate to support the weight of the entire fireplace/chimney system that will be sitting on it. Foundations should be built according to local building codes and/or NFPA 211 and shall be built on masonry, concrete or other noncombustible material having a fire resistance rating of not less than 3 hours. When building the foundation consideration should be made for the height of the hearth and hearth extension. If the finished hearth height is to be equal to the finished floor height, the foundation for the fireplace should be adjusted accordingly.

Hearth

The hearth of the firebox is the floor of the firebox. On the foundation, lay out the firebox floor 10 inches larger than the size of the firebox. Allow for the wall thickness of the firebrick that you will be using on the side and back walls of the fireplace. The end of each firebrick should line up with the centerline of the firebrick in the next row. Once satisfied with the layout, set the firebricks level in a bed of masonry mortar to form the floor (hearth).

Hearth Extensions

Hearth extensions should be built according to local building codes and/or NFPA 211 in size and materials

Building The Firebox

With the fireplace hearth bricks (floor) mortared in place, lay out the side walls and back wall. Bob Hart’s Rumford Fireplace Forms are designed for three standard firebox sizes. 36, 42, and 48 inch wide openings. The recommended dimensions for the Hart-Rumford Fireplace are;

Depth of firebox = 1/2 width of opening

Width of back wall = 1/2 width of opening

Height of fireplace opening = width of opening

In the example shown the front opening is 36” wide, therefore the back wall will be 18” wide. And the firebox depth is 18”.

At this point you need to decide if the firebrick will be laid with it’s wide (4 1/2” face) surface down, called a stretcher, or it’s narrow (2 1/4” edge) surface down, called a shiner. I prefer to build all of my fireboxes with the face down (stretcher). Laying the bricks flat uses twice as many brick but I feel it’s worth the extra time and expense to achieve a longer lasting firebox.

Drystack the first row of firebrick. Use a pencil and mark along both edges of the sides and back firebrick so you know where to position the bricks when you set them in refractory mortar. Using a good medium duty refractory mortar, butter each connecting surface of firebrick and as they are laid in place tap them carefully with a rubber mallet to level and set the brick into the refractory mortar. Only use a thin coat of refractory mortar—just enough to fill the voids between the firebrick. After every few rows, clean the inside surface of firebrick with a wet sponge to remove oozing mortar.

It is very important that each brick is laid level, plumb, and straight.

Where the sides walls and back wall meet, the corners should intertwine and overlap each other for the most strength, or for ease of replacement the sides and back can butt up to each other. A brick saw is very useful and makes a cleaner looking job, but if necessary use a brick hammer and chisel to make the needed cuts.

As the walls come up be sure all of your brickwork is remaining level, plumb, and     straight.

When you reach the height that is equal to the width of the fireplace opening (36, 42, or 48”), stop laying firebrick and build the outside walls of the fireplace up to the same height. 

The outside walls can be brick, block, stone or concrete. Fill all voids with regular mortar.

Setting The Hart-Rumford Fireplace Form in place

Protect floor if necessary.

Lay one leg of the form in front of ,and on each side of the fireplace opening with flat side down and multiple flange holes facing each other (facing center).

Slide the appropriate size breast plate (36, 42, or 48” wide) under the form. Align the three holes and bolt the breast plate to the center plate using the three 1/2” x1” bolts and nuts provided.

Next, slide the rear support pipe through the collar on the top of the breast plate until the bottom of the support pipe is approximately even with the bottom of the form legs. Then tighten the handle bolt against the support pipe.

Now with a helper, one person on each side of the form, stand the form up.

Set the form against the facing with a leg on each side of the fireplace opening. With two ratchet straps, secure the forms to the fireplace. Insert the hooks of the straps into the convenient holes in the outside flanges of the form legs. 

The breast plate should now be sloping upwards inside the fireplace opening. 

Adjust the rear support pipe to the desired height and tighten the handle bolt securely.

The Bob Hart Rumford fireplace form is now in place. 

Next continue laying up the firebrick following the edge of the breast plate and setting each firebrick back from the front of the brick beneath it. Use the breast plate as a guide as to how far to set each brick back. See Photo.

Continue until you reach the top of the breast plate. The back wall remains straight and the side walls narrow as you follow the breast plate to the top of the form.

Next build the outside walls of the fireplace to the same height. Fill all voids with brick and regular mortar. Secure the top of the form with a third strap.

Pouring the throat and lintel

Dampers

Bob Hart’s Rumford Fireplace Forms-parts